Silver_Dragon Posted September 4, 2013 Report Share Posted September 4, 2013 http://forums.eagle.ru/showthread.php?t=112658 DCS version 1.2.6 Change Log Note: The open beta version was not ready in time for release. DCS World Added new anti-ship penetrating warhead for anti-ship missiles. Increased Max G for the following missiles: R-60 (from 18 to 42), MICA (from 18 to 24), and R-40 (from 8 to 15). R-27ET: Decreased rear hemisphere DLZ. R-73: Corrected mass and thrust. R-77: Corrected time, fuel flow and thrust. SA-8 Osa: Increased range at low altitude from 6 to 8 km. Corrected the lock on range of IR missiles. Added Australia as a new country choice. Renamed APA-50 to APA-5D. Fixed error with coalition.addGroup()function. Added a new 3D model for the B-8V20 rocket launcher. Fog of War: Aircraft will no longer be visible on F10 map once it leaves line of sight of enemy units. Added exhaust smoke to Kusnetsov aircraft carrier. Kills are now tracked in the Log Book for Campaigns. Engagement range of ground units has been adjusted. Su-25T bomb Interval and Quantity are now working correctly. Trigger GROUP DEATH will working with event ON DESTROY. Fixed several SAMs ignoring the set "Alarm State Green". Debriefing: Fixed event recording. This will also correct log book errors. MiG-23 will now attack the moving ground target with rockets. Many minor corrections in the game. Wingman will report leader about enemy radar activity. Multiplayer: Radio communications are now working. Multiplayer: Debriefing window in the mission is now disabled for clients. Multiplayer: Fixed several crashes. New ambient sound system (sea, shallow water, fields, wind, g-breath effect). Wind + turbulence sound depends on mission weather parameters. New wingtip vortices, new touchdown smoke. Flaming Cliffs 3 (A-10A: DCS Flaming Cliffs) A-10A: Removed AAQ-28 TGP. A-10A: Corrected standby compass showing wrong heading. A-10A: Added PAC. A-10A: HUD fixed pitch angle indicator jumping from -90 to +90, when standing still on the ground is fixed. A-10A: Simultaneous engine start now working. A-10A: Fixed AIM-9 air to air mode. A-10A: Removed glideslope indication on the HUD. A-10A: Fixed ADI yellow vertical bar. A-10A: AoA indicator, indexer and AoA sound corrected. A-10A: Fixed HSI outer needle. A-10A: Added Stability Augmentation System (SAS). Su-33: Corrected AoA indexer. MiG-29 and Su-27/33: The vertical scan will not lock target automatically. Instead, player must press and hold the ENTER button to lock the target. Added RShift modifier to Kneeboard next/previous page commands (conflicted with Ka-50 Shkval track gate size controls). Su-25T: Removed targe diamond on the HUD. F-15C: Fixed altitude hold when air to air refueling. AWACS: Decreased the answer pause between picture requests. Corrected some missions. ATC now available for the Kusnetsov aircraft carrier. DCS: A-10C Warthog The engines will start after repair. If PTR switch is set to STOW and back to ABLE the pitch steering bar may freeze is fixed. A-10C. SAS and EAC switches fixed. DCS: Combined Arms Fixed multiplayer crash when land groups are assigned a route. Added German CA Manual. Smoke markers for controlled ground units are limited with 10 smokes at each color. Input: Absent joystick commands restored. HUD: Added cues of masking for line of firing by vehicle elements. HUD: Added health points indicator. MP missions replaced to MP folder. DCS: Black Shark 2 Added RShift modifier to Kneeboard next/previous page commands (conflicted with Ka-50 Shkval track gate size controls). Lighting night vision cockpit switch modifier moved to LCtrl to prevent conflict with Kneeboard ON/OFF key. DCS: P-51D Mustang Fixed no UNSAFE warning light and horn when throttle retarded. Quote Link to comment Share on other sites More sharing options...
hijijis Posted September 4, 2013 Report Share Posted September 4, 2013 Llegando a los dos gigas de descarga me da error de los servidores. ¿Le pasa a alguien mas? A mi también me ocurre.... me sale mensaje de error: "update servers can`t handle your request..".y bla bla ba. Creo que mañana lo intentare volver a actualizar y si no, bajaré la versión del torrent. Saludos. Quote Link to comment Share on other sites More sharing options...
D.Falcon One Posted September 4, 2013 Author Report Share Posted September 4, 2013 A mi me ha dado ese error, he cambiado la fecha he ejecutado el simulador y sin mayor problema, saludos. Quote Link to comment Share on other sites More sharing options...
SAFJFA F1 Team Posted September 4, 2013 Report Share Posted September 4, 2013 Bueno, yo aún voy por 850 MB . Saludos Quote Link to comment Share on other sites More sharing options...
Siegfried Posted September 4, 2013 Report Share Posted September 4, 2013 Yo por 940 nada mas... Quote Link to comment Share on other sites More sharing options...
Angel101 Posted September 5, 2013 Report Share Posted September 5, 2013 Aparte de pequeños Bugs como aviones levitadores en pista... estoy bastante contento con esta ultima actualizacion, carga como un tiro en comparacion a la 1.2.5 en modo offline. Si el online aguanta el tipo puede ser un buen salto de ver. Saludos. Quote Link to comment Share on other sites More sharing options...
Xifu Posted September 5, 2013 Report Share Posted September 5, 2013 A mi me parece un gran parche, los nuevos sonidos son la hostia, y los efectos tambien estan muy guapos. Una cosa que he notado es la optimizacion, aqui han hecho un gran trabajo, puedes meter muchas mas unidades de tierra y de la IA que los FPS no bajan tanto. Asi que buen parche por parte de ED...., si esto funcionase en Multiplayer ya seria la ostia. un saludo. Quote Link to comment Share on other sites More sharing options...
Disablez Posted September 5, 2013 Report Share Posted September 5, 2013 Si lo dice Xifu... tiene que ser weno. Stress test ! Quote Link to comment Share on other sites More sharing options...
Angel101 Posted September 6, 2013 Report Share Posted September 6, 2013 ¿Este finde? Por cierto alguien ha notado algo raro en el UFC del A10C? Quote Link to comment Share on other sites More sharing options...
Xifu Posted September 6, 2013 Report Share Posted September 6, 2013 Chicos ¿ habeis probado el refueling? No se si sere yo pero cuando pongo el dial 150.000 del tanquer sale un ruido como de modulacion y no contacta con el tanquer. Bug?, implementacion? Realista?. A alguien len ha pasado? Por otro lado me estoy dando cuenta de que el parche prometia mucho pwro viene con una cantidad de bugs impresionantes. Una ulttima pregunta, ¿ nonse suponia que este parche se tenia que testear antes de lanzarlo por langente que se apuntase?, yo no entiendo nada. Un saludo Quote Link to comment Share on other sites More sharing options...
Figueruelo Madrileño Posted September 6, 2013 Report Share Posted September 6, 2013 Yo no se vosotros, pero ami este parche me a desconfigurado completamente, en FaceTrackNoir, y a la hora de cargar las misione sy el multijugador se me hacen eternos :S Quote Link to comment Share on other sites More sharing options...
stirillas Posted September 6, 2013 Report Share Posted September 6, 2013 ¿Este finde? Por cierto alguien ha notado algo raro en el UFC del A10C? Pues si unas letras escritas como a mano en las teclas...no??? Saludos Quote Link to comment Share on other sites More sharing options...
lucifer Posted September 6, 2013 Report Share Posted September 6, 2013 Yo no se vosotros, pero ami este parche me a desconfigurado completamente, en FaceTrackNoir, y a la hora de cargar las misione sy el multijugador se me hacen eternos :S A mi me tarda mucho mas que antes en cargar las misiones y en salir de ellas. Ayer realice la instalacion limpia y sigue igual. Quote Link to comment Share on other sites More sharing options...
Zaz0 Posted September 6, 2013 Report Share Posted September 6, 2013 lo del UFC es copiado de los reales, de arriba a abajo y de izquierda a derecha, los 6 botones en los que han puesto las letras nuevas como pintadas son: - COMM 1 Used to send valid commands entered into the scratchpad to ARC-210-1, designate ARC-210-1 as the selected radio, and toggle on and off display of ARC-210-1 status in the HUD. Key depression for less than 1 second: • Entry between 1 and 25 into the scratchpad, commands ARC-210-1 to the simplex preset entered into the scratchpad. • Entry between 26 and 30 into the scratchpad, commands ARC-210-1 to the Half Duplex/Wideband SATCOM preset entered into the scratchpad. • Entry between 41 and 50 into the scratchpad, commands ARC-210-1 to the SATCOM/DAMA preset entered into the scratchpad. • Entry of 0 into the scratchpad, commands ARC-210-1 to the last valid manual frequency commanded to ARC-210-1 when ARC-210-1 is not already tuned to a manual frequency. • Entry of 3 to 6 digits into the scratchpad, commands ARC-210-1 to the manual frequency entered into the scratchpad. • Entry of 31 into the scratchpad commands ARC-210-1 into SCAN mode. • Entry between 1 and 25 into the scratchpad and depression of the ECCM key, commands ARC-210-1 to the ECCM preset entered into the scratchpad. • Entry of 26 into the scratchpad and depression of the ECCM key, commands ARC-210-1 to SINCGARS Cold Start. • Entry of 27 into the scratchpad and depression of the ECCM key, commands ARC-210-1 to SINCGARS Cue. • When the scratchpad is empty designates ARC-210-1 as the selected radio. • Key depression for more than 1 second toggles on and off the display of ARC-210-1 status in the HUD. - COMM 2 Same as COM1 for ARC-210-2. - COMSEC Used to toggle the COMSEC mode of the selected ARC-210 radio. • Key depression toggles the COMSEC mode of the selected ARC-210 radio between Plain Text, Cipher Text/Plain Text Only, and Cipher Text Only. - ECCM Used to designate an ECCM preset entry into the scratchpad and perform an ECCM preset toggle. • Key depression following numerical entry between 1 and 25 is used to enter a valid ECCM preset entry into the scratchpad. The ECCM preset is not sent to the radio until the COM1 or COM2 key is depressed. An "E" is displayed in the scratchpad following the entered preset number. • Key depression when the scratchpad is empty and the selected ARC-210 radio is set to a simplex preset, toggles to the corresponding ECCM preset. For example if ARC-210-1 is set to simplex preset 12, depressing the ECCM key when the scratchpad is empty will command ARC-210-1 to ECCM preset 12. • Key depression when the scratchpad is empty and the selected ARC210 radio is set to an ECCM preset toggles to the corresponding simplex preset. For example if ARC-210-1 is set to ECCM preset 12, depressing the ECCM key when the scratchpad is empty will command ARC-210-1 to simplex preset 12. - IFF Key depression triggers IFF functions: enable/disable Mode 1, Mode 3/A, or Mode C, Mode 1 or 3/A code updates, or Identification of Position (IDENT). • Pressing right upper blank right key with scratchpad empty sends IDENT to the IFF. • Entering a two digit Mode 1 code on UFC and pressing right upper blank key sends new Mode 1 code to IFF. • Entering four digit Mode 3/A code on UFC and pressing right upper blank key sends new Mode 3/A code to the IFF. NOTE If the CICU can not validate the Mode enable (1, 3, or 6), the CICU INPUT ERR message will display in scratchpad. • Entering “1” on UFC and pressing right upper blank key toggles Mode 1 On/Off. • Entering “3” on UFC and pressing right upper blank key toggles Mode 3/A On/Off. • Entering “6” on UFC and pressing right upper blank key toggles the Mode C On/Off. When a Mode C enable is activated by the UFC, the OSB is set to In Progress. If the OSB is already In Progress, the new enable is ignored. - IDM-RT Used to modify selection of radio for IDM data transmission, consistent with IDM Radio Selection OSB on COMM page (OSB 20). • Pressing key for less than one second, with no IDM/RT symbol on HUD (below ARC-210-2 radio status), displays the current selection for 5 seconds. • Pressing key for less than one second, with an IDM/RT symbol on HUD, cycles to the next selection (IDM/NONE, IDM/210 or IDM/164), displays the updated selection for 5 seconds. • The new IDM Radio selection also changes the rotaries on the COMM Page (OSB 20). NOTE If key is held longer than 1 second, the symbology is permanently displayed on the HUD until key is held again for longer than 1 second.[/spolier] Como podeis comprobar, se trata de la radio nueva, del IFF y del IDM, que no estan implementados en nuestra suite asique no tienen funcion, salvo decorativa Quote Link to comment Share on other sites More sharing options...
Blackleg Posted September 6, 2013 Report Share Posted September 6, 2013 Quote Link to comment Share on other sites More sharing options...
Figueruelo Madrileño Posted September 6, 2013 Report Share Posted September 6, 2013 Jo no consigo que me funcione el FaceTrackNoir ni el alabeo ni el cabezeo, aparte la transiciones en vhorizontal las hace alreves.....POR QUE¡¡¡¡¡¡¡¡ Quote Link to comment Share on other sites More sharing options...
wity Posted September 6, 2013 Report Share Posted September 6, 2013 Amí me ha dejado de funcionar el freetrack, y en la 124 y 123 sigue funcionando, será cosa del mod para el6dof del su 25T? Quote Link to comment Share on other sites More sharing options...
Hawat Posted September 6, 2013 Report Share Posted September 6, 2013 (edited) A veces con las actualizaciones se modifica el nombre del proceso por lo que si un programa externo tiene que comunicarse con él ya no lo encuentra. No conozco el API del facetrack ni del freetrack por lo que no sé si utiliza una comunicación entre procesos. Aún asi os lo digo por si os sirve de algo... (Bastaría con ver el nombre del proceso de las distintas versiones para comprobar si es igual o distinto) Edited September 6, 2013 by Hawat Quote Link to comment Share on other sites More sharing options...
Figueruelo Madrileño Posted September 6, 2013 Report Share Posted September 6, 2013 mmmmmm nose como se comprueba eso ...:S Quote Link to comment Share on other sites More sharing options...
Zaz0 Posted September 6, 2013 Report Share Posted September 6, 2013 Fotos de los UFC, Version original (FWR, MID, AFT) y version de la suite actual dentro del simulador http://www.lockonfiles.com/index.php?app=downloads&module=display§ion=screenshot&record=10073&id=1957 Version actual, foto real http://www.lockonfiles.com/index.php?app=downloads&module=display§ion=screenshot&record=10072&id=1957 Version intermedia (escrita a mano) en el simulador http://i1310.photobucket.com/albums/s655/Sharpe_74/Notgood_zps18b4dacf.png Y aunque habia visto fotos donde se veian perfectamente, ahora solo he encontrado esta del warthog real con las teclas pintadas.. http://farm5.staticflickr.com/4104/5173324627_c79e53202e_b.jpg Quote Link to comment Share on other sites More sharing options...
HABBI Posted September 6, 2013 Report Share Posted September 6, 2013 No suelo postear mucho, yo creo que es mi primer post, pero he visto una cosa en la nueva 1.2.6 que no me ha gustado nada, a lo mejor soy al unico que le pasa, pero no creo.En la cabina del a-10 en el panel que hay justo debajo del HUD han cambiado unos botones en los que ponia FWD AFT MID que no tenian funcion y ahora en vez de poner eso, salen unas letras que a mi parecer quedan un poco chapuceras pone I C I 2 E V ¿Que opinais? Quote Link to comment Share on other sites More sharing options...
Xifu Posted September 6, 2013 Report Share Posted September 6, 2013 No suelo postear mucho, yo creo que es mi primer post, pero he visto una cosa en la nueva 1.2.6 que no me ha gustado nada, a lo mejor soy al unico que le pasa, pero no creo. En la cabina del a-10 en el panel que hay justo debajo del HUD han cambiado unos botones en los que ponia FWD AFT MID que no tenian funcion y ahora en vez de poner eso, salen unas letras que a mi parecer quedan un poco chapuceras pone I C I 2 E V ¿Que opinais? Si hubieras leido el Post, te habrias dado cuenta de que la solucion ya esta dicha en el numero 39. http://www.escuadron69.net/v20/foro/index.php?/topic/57158-version-126-ya-disponible-aaa/page-2#entry849864 un saludo. Quote Link to comment Share on other sites More sharing options...
Zaz0 Posted September 7, 2013 Report Share Posted September 7, 2013 No suelo postear mucho, yo creo que es mi primer post, pero he visto una cosa en la nueva 1.2.6 que no me ha gustado nada, a lo mejor soy al unico que le pasa, pero no creo. En la cabina del a-10 en el panel que hay justo debajo del HUD han cambiado unos botones en los que ponia FWD AFT MID que no tenian funcion y ahora en vez de poner eso, salen unas letras que a mi parecer quedan un poco chapuceras pone I C I 2 E V ¿Que opinais? Pues mu mal, primero hay que presentarse.. Mirate el post que te ha dicho Xifu y el que postee yo justo antes que tu, hayaras tu respuesta joven padawan Te recomiendo que utilices la cabina de Ricardo, es mas bonita, real, sucia, ganas fps, y en el UFC vienen ya impresos esos botones, no a mano Quote Link to comment Share on other sites More sharing options...
Hellrequiem Posted September 7, 2013 Report Share Posted September 7, 2013 ¡RICARDO PITS! Pues a mi me va muy mal esta versión, en privado y en multi... en multi me cambio la configuración de mi servidor y ahora viene resultando que no puedo hostear misiones. Si te metes en una mision donde entran Steamers te jode por un .dll o algo así, y tienes que desactivar los modulos, activar el modulo de lo que vas a volar y reiniciar. Los FPS, muy muy mal cuando pongo al Mi-8... en fin, que es beta y toca aguantarse y reportar bugs... Quote Link to comment Share on other sites More sharing options...
Angel101 Posted September 7, 2013 Report Share Posted September 7, 2013 Por lo visto los que no hemos puesto el modulo del mi-8 la cosa va fina, fina. Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.